All Services

A Level 2 home charger turns an overnight plug-in into a full battery by morning, but only when it is wired correctly. Neighbors Electric installs home EV chargers across Fort Worth and the greater Dallas / Fort Worth metroplex, running a dedicated circuit sized to your charger and your vehicle so it charges at full speed without nuisance trips.

Why Fort Worth trusts Neighbors Electric

Drivers in Fort Worth, Southlake, and Grapevine call us because we plan the whole install, not just the outlet. We check whether your panel has the capacity, recommend the right breaker and conductor size, and route the circuit cleanly to the garage or driveway. If the panel needs attention first, we tell you up front.

Technical expertise and diagnostics

Most Level 2 chargers call for a dedicated 240-volt circuit, commonly 40 to 60 amps, wired per NEC Article 625 for electric vehicle supply equipment. We confirm the panel can carry the new continuous load with a load calculation, install a NEMA 14-50 receptacle or hardwire the unit per the manufacturer’s instructions, and add GFCI protection where required. We measure available capacity with a clamp meter and verify the finished circuit with a multimeter and receptacle tester.

Signs you need ev charger installation

• A new EV that charges slowly on a standard 120-volt outlet
• An existing outlet in the garage that trips when the car charges
• A charger manufacturer that specifies a dedicated 240-volt circuit
• Plans to add a second EV and the need to manage total load
• An older panel with no clear capacity for a new high-amp circuit

Our process

1. Review your charger model, vehicle, and panel capacity
2. Confirm available load and recommend breaker and wire size
3. Pull a permit where the jurisdiction requires one
4. Install the dedicated circuit and mount the charger or receptacle
5. Energize, test charging, and confirm no nuisance tripping

How we verify the work

We verify correct voltage and polarity at the receptacle or hardwire connection, confirm the breaker matches the charger rating, test GFCI function, and run a live charge test with your vehicle when possible to confirm full charging speed.

Why professional service matters

EV chargers draw high current continuously for hours, which is exactly the condition that exposes undersized wire and loose connections. A circuit that is close but not correct can overheat over time. NEC Article 625 exists specifically for this load type, and following it protects both the vehicle and the home. Learn more from the National Fire Protection Association.

Why choose Neighbors Electric

Neighbors Electric serves the DFW metroplex with licensed Texas electricians and clear, flat pricing. We size the install for your real-world charging, route it cleanly, and clean up when we are done. The neighbors you can count on.

Ready to schedule?

Call Neighbors Electric at 817-533-0943 for ev charger installation in Fort Worth and across the DFW metroplex. Licensed electricians, clear pricing, and the neighbors you can count on. 24-hour service available.

Frequently asked questions

What kind of circuit does a Level 2 EV charger need?

Most Level 2 chargers need a dedicated 240-volt circuit, usually rated 40 to 60 amps. We confirm the exact requirement from your charger’s specifications and size the circuit accordingly.

Can my current electrical panel handle an EV charger?

Often yes, but not always. We run a load calculation to confirm there is capacity. If the panel is full or undersized, we will explain your options before installing anything.

Should I get a hardwired charger or a plug-in unit?

Both are valid. Plug-in units on a NEMA 14-50 outlet are easy to replace or take with you. Hardwired units can support higher amperage and are sometimes required outdoors. We help you choose based on your charger and location.

Do I need a permit to install an EV charger?

Many DFW jurisdictions require a permit for a new 240-volt circuit. We pull the permit and schedule inspection wherever it applies.

How long does EV charger installation take?

A straightforward install is typically a few hours. Longer runs, panel work, or outdoor routing can extend that. We give you a time estimate with the quote.

Can you install a charger for two EVs?

Yes. We can install a second circuit or a load-managing setup that shares capacity safely between two chargers, sized to your panel.

Will the charger work at full speed after installation?

That is the goal of sizing the circuit correctly. We run a charge test when possible to confirm your vehicle pulls full power without tripping the breaker.